{

Sacrificial Anode vs Impressed Current: How to Choose, With Worked Examples

By Munawar Ahmad Mangla, Cathodic Protection Engineer

Choosing between a sacrificial anode system and an impressed current system is one of the first decisions in any cathodic protection (CP) design. Both protect steel in the same way, by supplying current to the structure. What differs is where that current comes from, how much you need, and how much attention the system will get over its life.

This guide walks through how to decide, then shows a simple sizing example for each type.

The short answer

  • Sacrificial anodes suit small current demand, good coating, lower soil resistivity and sites without power or regular inspection.
  • Impressed current suits large current demand, poor or bare coating, high resistivity soil and long or complex structures, as long as someone will maintain it.

Most real decisions come down to current demand, soil resistivity and who will look after the system.

Step 1: Estimate current demand

Every CP design starts with the current the structure needs:

Current required = surface area exposed to the soil x current density

Current density depends on the coating quality and environment. Well-coated pipe needs very little. Bare steel needs far more. If the answer is only a few milliamps or a few amps spread over small sections, sacrificial anodes are likely to work. If it runs to many amps, impressed current is usually more practical.

[Add the current density values you normally use for coated and bare steel in your region.]

Step 2: Check soil resistivity

Sacrificial anodes have a small driving voltage, so current output falls as soil resistivity rises. In low resistivity soil they work well. In high resistivity soil their output may be too small to be useful, and impressed current, with its adjustable voltage, is often the better choice. Measure resistivity along the route, for example with a Wenner four-pin test, and look at seasonal variation too.

Step 3: Consider power, access and maintenance

  • No power available nearby points to sacrificial anodes.
  • Remote or rarely visited sites favour sacrificial anodes, since they need little attention.
  • Impressed current systems need regular rectifier checks, readings and records. If that won’t happen, protection can quietly fail.

Step 4: Think about interference and neighbours

Impressed current systems can cause stray current effects on nearby buried structures if they are not coordinated and tested. Sacrificial anodes have much lower output and a lower interference risk. Where several operators share a corridor, factor this in.

Step 5: Compare life-cycle cost

Sacrificial systems usually cost less to install but may need anode replacement. Impressed current costs more up front and has power and maintenance costs, but a single groundbed can protect a large structure for a long time. Compare total cost over the design life, not just the installation price.

Anode materials at a glance

TypeCommon materialsNotes
SacrificialMagnesiumHigher driving voltage, often used in soil and higher resistivity areas
SacrificialZincLower driving voltage, common in low resistivity soil, water and marine use
SacrificialAluminium alloysMostly marine and seawater applications
Impressed currentMixed metal oxide (MMO)Long life, lightweight, widely used
Impressed currentHigh-silicon cast iron, graphiteUsed in groundbeds, often with coke breeze backfill

[Add the materials and suppliers you commonly specify.]

Worked example 1: sacrificial anode life (illustrative)

Suppose a magnesium anode weighing 7.7 kg is expected to deliver an average of 40 mA. Assume a magnesium capacity of about 1,100 Ah/kg and a utilisation factor of 0.85.

Anode life (years) = (weight x capacity x utilisation) / (current x 8,760 hours per year)

= (7.7 x 1,100 x 0.85) / (0.04 x 8,760)

= 7,199.5 / 350.4

= about 20.5 years

In a real design you would use the manufacturer’s data for capacity and check output with actual soil resistivity. If the required life is longer, you would use a larger anode or more anodes.

Worked example 2: current demand for an impressed current system (illustrative)

Consider a coated pipeline 10 km long with a diameter of 0.5 m.

Surface area = pi x 0.5 m x 10,000 m = about 15,700 m2

Assume a design current density of 20 microamps per m2 for the coated steel:

Current required = 15,700 x 20 x 10^-6 A = about 0.31 A

In practice you would add a margin for coating deterioration over time, then size the rectifier and groundbed to deliver that current at an acceptable circuit resistance and anode life. Real designs also account for coating breakdown factors, soil conditions and the groundbed design.

[Add your own example from a project, with figures you can share.]

Can you use both?

Yes. Many projects use impressed current for the main line and sacrificial anodes for isolated sections, branches, or areas where more local protection is needed. Hybrid designs are common in plants and on long pipelines with varied conditions.

Quick decision guide

  1. Estimate current demand from area and coating condition.
  2. Measure soil resistivity.
  3. Check power availability and maintenance capacity.
  4. Consider interference with other structures.
  5. Compare life-cycle cost.
  6. Choose sacrificial, impressed current, or a combination, and confirm against the standard and specification for your project.

Key takeaways

  • Start with current demand, since it often settles the question.
  • Sacrificial anodes are simple and low maintenance but limited in output.
  • Impressed current is powerful and adjustable but needs power and monitoring.
  • Soil resistivity, interference and long-term maintenance matter as much as cost.
  • [Link: Cathodic protection: how it works]
  • [Link: Cathodic protection for boreholes]
  • [Link: How to read a pipe-to-soil potential survey]

About the author: Munawar Ahmad Mangla is a cathodic protection engineer. [Link to author page]

Leave a Comment